Re: HP Flex10 and recommended vDS config for HA and failover?
Beacon Probing will require 3 NICS to work correctly. http://theithollow.com/2012/03/understanding-beacon-probing/ It sounds like your virtual connect ICs are in an Active-Passive mode correct? Or...
View ArticleRe: Windows 8 BSOD at 7% battery warning
Isn't that the same thing that I attached on 16th Dec (see further up in this thread)? If it's something else, let me know how to collect it. Also, since you're asking for my memory dump, does that...
View ArticleRe: New-VM commandlet performance is too slow
No I dont find any difference between first New-VM and any subsequent New-VM in the same session. All the to,e its taking same time which I alwardy mentioned. Let me try soluction which you have...
View ArticleRe: VM Help needed. (Server 2.0.2)
Hi, Moved your discussion thread to "VMware Server 2, installation and upgrade" section of the forums. --Wil
View ArticleRe: ESXi partition
if it was esx... it will ask.. but in esxi it wont ask... if you do any kick start.. or scripted installation you can specify...but normally not needed and esxi is very inteligent.. to do efficient...
View ArticleClik here to view.
Re: VMWARE Fusion 5 and my iMac
Wil van Antwerpen wrote: Then go into Fusion menu "Virtual Machine", "Settings", "Hard Disk" and increase the size.On starting your guest OS, the virtual disk will be bigger. While that is true...
View ArticleRe: HP Flex10 and recommended vDS config for HA and failover?
i have also a similar setup like you, c7000 with g7 blades... so basic thing in the HP-VC is to enable smart link in the VC, ie for when you define each VLAN in the VC you need to enable this.This...
View ArticleRe: New-VM commandlet performance is too slow
Coud you please help in resolving following error... After running command ... PS vN:\> C:\Windows\Microsoft.NET\Framework64\v2.0.50727\ngen.exe install "VimService51.XmlSerializers,...
View ArticleRe: VSA Cluster Network - Using EtherChannel / Link aggregation
santhoshnz wrote: I understand all the hosts in the VSA cluster must have two dual-port or four single-port network interface cards for the VSA network configuration. Is it possible to have...
View ArticleRe: Installation error: VSA Manager should be installed on the vCenter Server
I ran into this exact issue. vCenter Server was installed onto a host joined to the domain handling Single Sign On authentication, which mandated installing with Domain Admin credentials. The error...
View ArticleVSA 5.1 with Link Aggregation?
Is it possible to use static link aggregation for VSA Front End and Back End networks? Greenfield installs complain about vSwitch0 having a LAG configured instead of NIC teaming with failover. A...
View ArticleRe: ESXi Management not working Cisco LAG
Before you do too much work on getting static link aggregation working, you might want to consider that VSA won't do a brownfield installation onto vSwitches with anything except NIC teaming with...
View ArticleRe: New-VM commandlet performance is too slow
In your first post you said that that you are using PowerCLI 5.0. The command that doesn't work uses a PowerCLI 5.1 file. I would suggest to upgrade to the latest PowerCLI version first and then try...
View ArticleRe: New-VM commandlet performance is too slow
That means, mentioned performance setting is for powercli to 5.1?
View ArticleRe: New !! Open unofficial storage performance thread
Server Type:Win 2008R2 on ESX 5.1Host Type:Dell R320Storage Type:LOCAL PERC H310 RAID 10 4xSAS 600GB 15kAvg Resp. Time msAvg IOs/secAvg MB/sec% cpu loadMax...
View ArticleRe: New-VM commandlet performance is too slow
No, only that single command is for PowerCLI 5.1. The blog post Luc mentioned might be a bit confusing. Take a look at the original blog post from the PowerCLI team How to speed-up the execution of the...
View ArticleAndroid Tablet Access
I currently run the free ESXi 5.0 at home, and thinking of buying the Nexus 10 Tablet.. What do I need to install on the tablet and/or the ESXi server that will let me 1) Access the vSphere client2)...
View ArticleRe: Management interface failes after changing IP of vmotion vmkernel port
thats right - i wanted but i didn't...the plan was to move the vmotion network to a seperate vlan. the first step was changing the ip-adress of the vmotion vmkernel port - not more (the vlan on the vm...
View ArticleMAC keyboard and special characters
I am not able to use the special character "\" in control center. I am running a MAC OSX 10.8 with Danish Enhanced keyboard and I have set the user preference in Control Center (Windows 2008) according...
View Article